1133A Power Sentinel CSV Release Log
Release 1.116
Bugs Fixed:
- Modem connection fixed
- Set Time Deviation function fixed.
Release 1.114
New Features / Improvements:
- Updated copyright notice to 2008
Bugs Fixed:
- Wave data columns BV and BI were swapped with columns CV and CI when exported to PQDIF
- Saved phase data with freq configuration of 50Hz displayed as 60Hz when reloaded and displayed RS485 communication was noncommittal.
Release 1.113
Bugs Fixed:
- RS485 communication was noncommittal.
- PQDIF file exporter time was off by 2 days.
Release 1.112
New Features / Improvements:
- Add support for new redesigned 32MB data Flash memory card.
Release 1.111
Bugs Fixed:
- Waveform display had B and C phases transposed.
Release 1.110
Bugs Fixed:
- Fixed export from downloaded session where data was missing. PSCSV -> download session -> export to scheduled doc -> open and view sched doc.
Release 1.108
Bugs Fixed:
- Added back in smooth wave interpolation, and it's smart enough to stop interpolating when there isn't enough space between data points to do so.
Release 1.107
Bugs Fixed:
- Configuration Capture did not capture all configuration.
- Removed factory set hardware configurations items. Allowed units to
New Features / Improvements:
- PSCSV will no longer support old phasors. Use earlier versions if you need to look at old data, configure old units, etc.
- Reworded config capture to configuration create/edit.
- Added defaults for scheduled sequence and register counts.
- Now asks for and receives new PMU broadcast.
Release 1.103
New Features / Improvements:
- Added new PMU configuration and Ethernet status update.
- Power Factor and Q bits are now in the Analog Power Section for each PMU
Release 1.100
Bugs Fixed:
- The very last record in a series of contiguous records wasn't being exported.
New Features / Improvements:
- PQDIF doesn't like observations with the same name and the same time (TOP only uses the time to the nearest second). PSCSV now assigns new observation names for each observation by appending an increasing integer ("AV Wave1", "AV Wave2", etc.)
Release 1.099
Bugs Fixed:
- PQDIF time discrepencancies.
- Daylight Savings Pref change so that all spreadsheet-like views update automatically.
New Features / Improvements:
- Turned off firmware version warning altogether.
- Turn back old behavior in pscsv.ini:
Release 1.097
Bugs Fixed:
- Fixed waveform view, no longer says "no data" where there really is data.
- DSP log view fixed.
New Features / Improvements:
- Broadcast harmonics are now configurable.
- Increased number of digits for individual waveform samples.
- Export to COMTRADE from 1133 event waveform.
- Waveform now uses time discontinuities to show breaks between events. Red arrows navigate to beginning of wave.
- PQDIF from waveform.
Release 1.090
Bugs Fixed:
- Fixed port selection Disabled, Inactive, TCP, Broadcast, Unicast, Multicast
New Features / Improvements:
- Split code between 1133A and 933A. There is a new PSCSV package specifically for the 933A
- Comtrade export improvements
Release 1.081
Bugs Fixed:
- Fixed a problem where PSCSV was not properly listening to UDP.
Release 1.079
Bugs Fixed:
- Fixed where 1133 downloaded event DSP & System log documents were viewed as empty.
- Fixed event waveform cursor alignment.
Release 1.077
Bugs Fixed:
- Fixed download session export crash.
- Fixed Export to CSV - exports to UTF-8.
- Fixed crash where a very slow to answer broadcast.
- Fixed summary view where it wasn't updating on a broadcast.
- Fixed the security reset dialog to recognize valid keys.
New Features / Improvements:
- Added capability to communicate with 933A
- C37 broadcast enabled
- Sparkline renamed to Summary.
- All .ini access unified.
- Event docs display summary view by default too.
- Adds nominal line to phasor frequency view when Auto Scale is off.
Release 1.068
Bugs Fixed:
- Fixes download session export crash.
- Adds nominal line to phasor frequency view when Auto Scale is off.
- Fixes Export to CSV for Chinese (and everyone else) - exports to UTF-8.
New Features / Improvements:
- All .ini access unified.
- Sparkline renamed to Summary.
- Event docs display summary view by default too.
Release 1.067
Bugs Fixed:
- Fixed broadcast bug
- Fixed Tip of the day persistence.
- Made PSCSV go slow for benefit of PS. This isn't expected to be a long term fix, rather it is a workaround.
- Fixed sparkline not intializing properly (it assumed that it had enough information too early)
- Fixed the UDP broadcast for the new C37 phasors.
- A couple of small changes were put back in so that PQDIF could work again that the UNICODE version broke.
- The phasor frequency view is back. This is a display only feature, the whole condition / action is gone for good. Customers that want that should really think about using PS triggers or use something like OSISoft's PI or write their own using PSCL.
New Features / Improvements:
- Small improvements for 933, including CTPT editing.
- A lot of internal changes for loading / storing preference data. It's still in progress but is usuable. Preference lookup is a lot faster on account of the preference data being cached.
- The fonts for realtime, phasor and waveform are all the same and are modifiable through the new preferences dialog. The preferences dialog is going to expand a bit.
- Realtime view lost a few preferences and has bug in filtering, but is going to gain a bit more soon.
- The installer now is supposed to abort on anything but an NT based architecture.
- Basic, Energy, etc. no longer ask the user to select every single data item. All of the are requested from the unit. Users should use the View > Filter to limit and reorder what they see. Harmonics is the only exception and only requests the first few harmonics - this will be configurable too.
- New sparkline summary view. This is the default for the indexed documents. You can reorder and filter the displayed items using the View > Filter Data menu.
- All of the views now use the same font, including the spreadsheet views (which had their grid lines removed).
- All but harmonics broadcast requests all of the data now. No more need to individually select each item.
Release 1.062
Bugs Fixed:
- Fixed the UDP broadcast for the new C37 phasors.
New Features / Improvements:
- UNICODE release that allows for internationalization of the menus.
Release 1.059
New Features / Improvements:
- New C37.118 configuration, broadcast and event.
Release 1.026
New Features / Improvements:
- Dowloads and displays Sag & Swell events. Can export them as CSV.
- Fixed the web link in the Tip of the day #10.
Release 1.024
New Features / Improvements:
- Ability to open scheduled data downloaded using the PSDownloader
Release 1.010
Bugs Fixed:
- Replaced the top grid with a set of edit controls as a workaround for a windows bug.
- Fixed a bug where PSCSV wasn't updating it's UI when it received some Sag & Swell config data.
- Fixed the flash overwrite/configuration
New Features / Improvements:
- The trigger dialogs are related. Set a trigger in one, and the other notes it and prevents you from configuring sub items.
- Now has an Off as the first item in the Channel selection. The Channel selection has the newer definition (in user oder: AV, AI, BV, BI...). The functions have been updated as well. Lastly, the input references have been added to the top of the UI.

